Anytime, anywhere, your bike tyre can get damaged. We often seek a professional to change your flat tyre. If you ever find yourself stranded without access to a mechanic or tyre shop, this knowledge will be helpful. Even the best-made vehicle or motorcycle tyres can get punctures; this is unavoidable. It is recommended to replace your bike tyre within 5 years of its manufacturing. After a long drive, you might, however, experience severe damage and decide to change it yourself even sooner.
The main thing to remember in such a situation is how to properly remove and install a tyre. Using improper techniques can damage your motorcycle and lead to problems in the future. Therefore, if you’re unsure of how to change a bike tyre, you should be aware of the following methods. So, let’s learn how to change a flat or damaged tyre on your bike by ourselves.
Here’s how you can change a bike tyre and our 10 Steps to patch up a punctured tyre on your bike in less than 20 to 30 minutes.
The following things are required before we start to change a bike tyre:
• Valve core tool
• Bead breaker
• 2 C-clamps (optional)
• Tyre irons or spoons
• Silicone lubricant spray
• Breezed tyre tool
• Air pump compressor
Step 1: First, take your motorcycle’s wheel off.
Lifting the end of your bike is the first step in removing the axel. Next, pull the wheel of your bike off the ground. Once its chain is released, remove the brake caliper. the caliper’s position can then be determined by putting its axel back.
Step 2: Take Away the Schrader Valve and Allow the Air to Escape.
Filling and maintaining the air pressure in your bike tyres depends heavily on the Schrader valve. Making it simple for you to replace the tyre is to entirely let the air out of it. To keep the valve exposed, a valve core tool must be used to screw or snap into it. To prevent the air from leaking out, grip this tool firmly.
Step 3: Mark Spin Direction of Your Wheel.
To indicate the direction that your wheel is turning, draw an arrow using a marker at the outer edge of your bike’s rim. In order to prevent fading caused by lubricant spray throughout the subsequent procedures, use a permanent marker. You must replace the wheel in the same direction that it is spinning, thus this step is crucial. If you’re learning how to change a bike tyre, this very minor but crucial step is the first one.
Step 4: Break the bead on your bike tyre.
Your bike tire’s inner edge that connects to the rim of the wheel is known as the bead. You can start moving it around the bead of the tyre by inserting it with a bead breaking tool between the wheel rim and tyre. To make sure it doesn’t stick back, spray silicone lubricant or a solution of soap and water. Next, turn your wheel over and proceed in the same manner on the opposite side. Another option for removing the beads is to use a C clamp.
Step 5: Remove the Tire from the Rim of Your Bike.
To lift the bead and remove it off the rim, you must use at least two tyre levers or spoons. These “spoons” or “tyre levers” are nothing more than metal tubes. To remove your bike tyre, carefully tuck one lever under the bead and push it downward. After then, place a second lever a few inches distant from the previous one and maintain it there. After that, take out the first lever and nudge it a little bit away from the starting position. Repeat these steps on the opposite side of your bike until your tyre completely separates from the rim. Do the same with the second rim.
Step 6: Clean and lubricate the interior of the rim and the new tyre.
This is yet another crucial phase of bike tyre replacement. Make sure there is no remaining debris by cleaning the interior of the rim. Bead lubricant should also be applied to the boundaries of your new tyre. Any hand soap or sanitizer will do, as they all function the same.
Step 7: Install the New Tire on the Rim of Your Bike.
You can buy a quality & a budget new tyre online by checking tyre models https://tvseurogrip.com/product-category/two-wheeler/
Put the new tyre on the rim in the same way that you had previously marked it to spin. Additionally, pay attention to a red dot on the bike’s tyre that you must find next to the valve stem. These elements are crucial to making sure that all of your future effort is not in vain.
Step 8: Mount Your Bike’s Tire to the Rim on One Side.
This step is crucial if you’re thinking about how to install a new bike tyre. Utilizing the tyre spoons, squeeze and push your tyre under one side of the rim. Flip the wheel over and carry out the same procedure on the opposite side of the rim.
Step 9: Reinstall the valve stem and inflate your tyre.
Start putting air in your tyre, but don’t fully inflate it until you hear it explode. If you don’t hear that “pop” while pumping up the tyre on your bike, you may always use a Breezed tool to push the bead in. Reinstall your valve stem and tighten it one more after that. Finally, you can fully inflate this tyre to its specified pressure until it is the proper width for the rim.
Step 10: Remount the motorcycle’s wheel.
Finally, reinstall the wheel in accordance with your user’s handbook and check the air pressure in your motorcycle’s tyres once more. Additionally, be sure you tighten all of your vehicle’s fasteners, adjust the chain tension, and line both wheels with one another.
Here’s how you can Change a Bike Tyre and Fix a Flat Tyre and correctly fix a puncture. Keep this article as your handy manual for getting yourself out of a flat tyre crisis. Safe driving!
TVS EUROGRIP – THE BIKE TYPE SPECIALIST
